Yahoo France Recherche Web

Ouvrir une session

Résultats de recherche

  1. Signal - Busy

    • A
      Le Signal
      Location De Bureaux Équipés · Fermé
      2 r Irène Joliot Curie, Les Auxons · 0381878800
    • PagesJaunes
      En partenariat avec  

    Tout afficher

  2. community.cisco.com › t5 › webex-callingIntermittent busy signals on incoming calls via Webex Calling

    25 févr. 2022 · Otherwise, I'd suggest to raise a TAC case with providing exact timestamps/numbers so that they can look into it. 02-25-2022 09:24 AM. We are using CCPSTN. 02-25-2022 09:18 AM. We have not had any of such issue, also I did not heared anthing like that in some other Calling spaces..

  3. community.cisco.com › t5 › other-collaboration-subjectsBusy Signal - Cisco Community

    16 mai 2002 · If you are getting a busy signal from either switch when Unity is reporting that all ports are idle, you'll probably have to gather traces from CCM or Unity. Unity itself, cannot produce a busy signal. It can however, produce a situation where the PBX would return busy signal to the caller: all of its ports are busy.

  4. community.cisco.com › t5 › ip-telephony-and-phonesSolved: voicemail busy tone - Cisco Community

    16 juil. 2019 · voicemail busy tone. 07-16-2019 07:40 AM. I have one user when they hit the voicemail button on the 7821 IP phone they hear a busy signal. No one else is having issues. 07-16-2019 12:41 PM. voicemail profile is set to default and mine is too (from my phone I can reach voicemail). I checked this user is in Unity and does have a mailbox.

  5. community.cisco.com › t5 › ip-telephony-and-phonesSolved: Outgoing calls - Fast Busy tone - Cisco Community

    1 mai 2016 · In response to flores.fernando1. 05-01-2016 10:29 AM. Can you attach "debug isdn q931" traces of one incoming call, so we see what plan & type service provider is using and we can apply the same for outbound calls. Below is the example to change it. Step 1: Create a translation rule. voice translation-rule 10.

  6. community.cisco.com › t5 › ip-telephony-and-phonesRemote Destination - Busy Signal - Cisco Community

    24 mai 2018 · A translation pattern would be a less complex setup but I wouldn't worry about it at this point since you're getting a legit busy signal. I wonder if the call is looping back to the system causing the busy signal. Can you change the remote destination number to your cell number and test? That will verify that the call is routing properly and ...

  7. community.cisco.com › overhead-paging-giving-continuous-busy › td-poverhead paging giving continuous busy - Cisco Community

    15 déc. 2009 · Level 1. 12-15-2009 08:38 AM - edited ‎03-18-2019 10:56 AM. Hi, we had a power outage last week, after that overhead bogen system is continuously giving a busy noise. Bogen is connected to an ATA, it has to be turned off due to conitnous busy sound. I have checked the 2811 config and it seems ok. Thanks.

  8. community.cisco.com › t5 › voice-over-ipVG204 with a busy signal? - Cisco Community

    13 déc. 2012 · victoriabardy. Level 4. Options. 12-13-2012 03:49 PM. Hello all, I have a strange situation with a new vg204 analog gateway. I have it configured and registered with the call manager but when I attach an analog phone I get a steady busy signal? Pls see the config below: USDTW1VG204-1# show run.

  9. community.cisco.com › t5 › ip-telephony-and-phonesSolved: Meet Me Conf Bridge - Cisco Community

    22 févr. 2010 · Level 1. In response to CHRIS CHARLEBOIS. Options. 02-22-201011:57 AM. There is a conf bridge configuration in the media resource group. When you press the Meet Me softkey and get the two short beeps to enter the dn, you get a busy signal after you enter the dn assigned for the Meet Me Number Configuration.

  10. community.cisco.com › busy-signal-with-incoming-calls › td-pSolved: Busy signal with incoming calls. - Cisco Community

    12 nov. 2009 · Level 1. Options. 11-12-2009 03:11 AM - edited ‎03-21-2019 01:46 AM. Hi all, I have a problem with the incoming calls. I hear only one tone and the next a busy signal. I don't know if the configuration is correct, the outgoing calls working fine. Many thanks for all. Best Regards. M.Castilla.

  11. community.cisco.com › t5 › ip-telephony-and-phonesCisco ATA 187 - Fast busy Tone - Cisco Community

    9 févr. 2011 · Options. 04-15-2011 03:11 PM. I am having the exact same issue. I have figured out what the problem is but I have no fix. In the ATA 186 you can configure the reorder tone delay. In fact you can turn it off in the ATA 186. In the ATA 187 you cannot. The fast busy signal you hear is actually the reorder tone. In the ATA 186 you can use a 32 bit ...